V Series Zone Audio Platform
Clean power for every zone.
V600:4 4-Channel Power Amplifier
600 W across four channels in one rack unit, with powerTANK and ecoRAIL.
V Series Zone Audio Platform
Clean power for every zone.
V600:4 4-Channel Power Amplifier
600 W across four channels in one rack unit, with powerTANK and ecoRAIL.
V600:4 One Amplifier,Any Speaker Line.
4-Channel Power Amplifier
600 W total power · 4 independent channels · Full 70V / 100V support
V600:4 One Amplifier,Any Speaker Line.
4-Channel Power Amplifier
600 W total power · 4 independent channels · Full 70V / 100V support
Dynacord V600:4 Product Highlights
Explore the key capabilities of the Dynacord V600:4 zone amplifier.
powerTANK
Shares 600 W across channels where needed.
Any Load
Each channel 4 ohm, 8 ohm, 70 V or 100 V.
One-Cable Input
RJ45 input takes four zones from the VZX-8.
Built-In DSP
High-pass, 150 Hz low-pass and limiter.
Energy Saving
Auto Power Down to under 1 W.
Compact
1U.
Full-Width 1U Rack Design
The V600:4 measures 483 × 44.2 × 269.5 mm (W × H × D) and weighs 3.6 kg. It takes up a full 19" rack unit (1U), so it fits into standard equipment racks alongside the VZX-8 and other rack-mount gear without needing an adapter.
Simple Mounting
The V600:4 ships with 19" rack mounting brackets pre-mounted, so it installs directly into a standard rack with no extra hardware. Four rubber feet are also included for tabletop use when a rack isn't available.
Ventilation & Placement
Airflow runs side-to-rear. Leave space between units when stacking multiple amplifiers in a rack, since the V600:4 relies on convection cooling in normal use and only engages its fan under extreme thermal load. Keep it away from direct sunlight and heat sources. It operates reliably from -5°C to +45°C.
Key specs
- 4 x 150 W rated, 600 W total (powerTANK)
- One channel up to 500 W (4 ohm / 70 V) or 600 W (8 ohm / 100 V)
- Direct drive 70 V / 100 V, no transformer
- Euroblock inputs + RJ45 (AES72-1E)
- HPF 100 / 150 Hz, LPF 150 Hz, peak limiter
- Remote on / standby, ready / fault relay
- Auto Power Down under 1 W
- 1U, 483 x 44.2 x 269.5 mm, 3.6 kg
Technical Specifications
| Specification | Value |
|---|---|
| Product | V600:4-EU Power Amplifier, 600W, 4 Channel |
| Amplifier Class | Class D, fixed frequency |
| Number of Channels | 4 |
| Total Rated Output Power | 600 W |
| Rated Output Power per Channel | 4 × 150 W |
| Power Technology | powerTANK power sharing between channels |
| Load Handling | Variable Load Drive (4 Ω, 8 Ω, 70 V, 100 V, on any channel simultaneously) |
| Signal Processing | Input routing, HPF 24 dB/oct (100/150 Hz), LPF 24 dB/oct (150 Hz), flat, peak limiter |
Electrical Specifications
| Specification | 4 Ω | 8 Ω | 70 V | 100 V |
|---|---|---|---|---|
| Max Output Power per Channel (power sharing, at min. impedance) | 500 W | 600 W | 500 W | 600 W |
| Output Voltage at Rated Power | 24.5 VRMS | 34.6 VRMS | 70.7 VRMS | 100 VRMS |
| Maximum Output Voltage | 40.0 VRMS | 56.0 VRMS | 70.7 VRMS | 100 VRMS |
| Rated Impedance per Channel | 4 Ω | 8 Ω | 33.3 Ω | 66.7 Ω |
| Minimum Impedance per Channel | 2.6 Ω | 4 Ω | 10 Ω | 16.7 Ω |
| Nominal Gain (+6 dBu sensitivity) | 24.0 dB | 27.0 dB | 33.2 dB | 36.2 dB |
| Maximum Gain (0 dBu sensitivity) | 30.0 dB | 33.0 dB | 39.2 dB | 42.2 dB |
| Damping Factor | > 80 | > 160 | > 500 | > 1000 |
| Signal-to-Noise Ratio (A-weighted) | > 98 dB | > 100 dB | > 101 dB | > 103 dB |
| Output Noise (A-weighted) | < -68 dBu | < -67 dBu | < -62 dBu | < -61 dBu |
| Crosstalk | < -70 dB | < -75 dB | < -90 dB | < -95 dB |
| Frequency Response (-3 dB) | HP: 30/100/150 Hz to 20 kHz; LP: 30 to 150 Hz | HP: 30/100/150 Hz to 20 kHz; LP: 30 to 150 Hz | HP: 50/100/150 Hz to 20 kHz; LP: 50 to 150 Hz | HP: 50/100/150 Hz to 20 kHz; LP: 50 to 150 Hz |
| Specification | Value |
|---|---|
| THD+N (1/8 rated power, 1 kHz) | < 0.1% |
| Power Requirements | 100 V to 240 V AC, 50 Hz to 60 Hz |
| Power Supply Topology | Switching power supply with power factor correction |
| Power Consumption (1/8 rated output) | 115 W |
| Idle Mode (ecoRAIL, no input signal) | < 20 W |
| Standby Mode (Auto Power Down active) | < 1 W |
Connectivity
| Specification | Value |
|---|---|
| Analog Audio Input | 2 × 6-pin Euroblock (3.81 mm, male), in parallel with 1× RJ45 (AES72-1E) |
| Maximum Input Level (Level 0 dB) | +18 dBu |
| Input Impedance | 20 kΩ, active balanced |
| Loudspeaker Output | 2 × 4-pin Euroblock (5.08 mm, female) |
| Mains Input | IEC C14 |
| Control Port | 1 × 5-pin Euroblock (3.81 mm, male) |
| Remote On / Standby | Contact input (overrides front-panel power button) |
| Ready / Fault | Galvanically isolated relay, max 30 VDC / 500 mA DC |
| Front Status LEDs | Signal, limit and fault LEDs per channel; power LED |
Mechanical Specifications
| Specification | Value |
|---|---|
| Form Factor | 1U, 19" rack width (tabletop use with included rubber feet) |
| Dimensions (H × W × D), with 19" brackets | 1.74 in × 19.2 in × 10.6 in / 44.2 mm × 483 mm × 269.5 mm |
| Weight | 7.9 lb / 3.6 kg |
| IEC Protection Class | Class I (grounded) |
| Cooling Concept | dualCOOL: convection on a tabletop or in a rack with spacing; forced cooling (side to rear) in a rack without spacing or in extreme thermal conditions |
Environmental Specifications
| Specification | Value |
|---|---|
| Ambient Temperature Limits | -5 °C to +45 °C / +23 °F to +113 °F |
| Operating Altitude | -500 m to +5000 m / -1614 ft to 16404 ft |
Protection Features
| Specification | Value |
|---|---|
| Protection Package | Audio limiters, high temperature, DC, HF, short circuit, back-EMF, peak current limiters, inrush current limiters, mains over/under voltage protection |
| Named Protections | HFL, OCL, RSL, HFP, DCP, OCP, MFP, OBP, OTP, OVP |